Accordion M1 MPIO & Power Supply
Product brief
The Accordion M1 MPIO & Power Supply is a ready-to-run configuration of the compact Accordion M1 platform for PCBA test, NPI and small-scale production test. It combines 96 reconfigurable mixed-signal channels with a two-channel programmable power supply on one network-attached node.
The unit contains an Accordion M1 mainboard with a Raspberry Pi 4, pre-fitted with three modules:
-
ESH10000568 MPIO-96 SPI Module — 96 channels, each configurable as analog input, analog output or pseudo-digital I/O.
-
ESH10000355 6× IDC N-Top Breakout Module — the 96 channels on six 20-pin IDC connectors, with an RGB LED per connector.
-
ESH10000662 Mini-PSU — two independent programmable outputs, 5–24 V, up to 1.5 A each.
The M.2 slot is free for expansion.
The unit ships with lifetime licences for Accordion Shell and Accordion Pilot.
Typical use cases:
-
Functional and parametric PCBA test that needs mixed-signal I/O and one or two programmable DUT supplies.
-
Bring-up benches where channel roles change during test development.
-
Production fixtures connected over 20-pin IDC ribbon cable.
Key constraints:
-
96 user signals, routed 1:1 from the MPIO-96 to the IDC connectors — no signal conditioning, no multiplexing.
-
MPIO-96 analog range: 12-bit ADC and DAC, 0–5 V typical (AD5592R 2× mode).
-
IDC connectors: 5 V max, 2 A max per signal pin; the pin-1 (5 V) and pin-2 (20 V) rails are PTC-fused at 0.25 A per connector.
-
Mini-PSU: 1.5 A continuous per channel up to 20 V output; above 20 V each channel is limited to about 30 W.
-
Powered over USB-C (USB-PD) at 20 V. The bundled power supply is the only supported supply.
Datasheet
System
|
Parameter |
Value |
Notes |
|---|---|---|
|
Product name |
Accordion M1 MPIO & Power Supply |
|
|
Part number |
ESH10000725 |
|
|
Platform |
Accordion M1 (mainboard ESH10000597) |
|
|
Controller |
Raspberry Pi 4, 4 GB |
|
|
Firmware |
Accordion 6.0.0 or later |
|
|
Power input |
USB-C (USB-PD) 20 V, via the bundled 130 W power supply |
Use the bundled supply only. |
|
Power-on |
At power-up or with the power button |
Optional, set at delivery. |
|
Input current, idle |
≤ 0.30 A at 20 V (≤ 6 W) |
PSU outputs off. Tested on every unit. |
|
Input protection |
eFuse, 5 A current limit, overvoltage cut-off above 21 V |
|
|
Network interface |
Ethernet, Wifi |
|
|
Module slots populated |
SO-DIMM (MPIO-96), N-Top (IDC breakout), COMTOP (Mini-PSU) |
|
|
Module slots free |
1× M.2 |
|
|
Cooling |
Active, one fan, speed-regulated by the Accordion process |
Full speed at boot. |
|
Enclosure |
Hammond 1455K1201BU with E# front and back panels |
|
|
Dimensions (L × W × H) |
120 × 78 × 43 mm |
|
|
Weight |
324 g |
|
|
Compliance |
CE, RoHS, REACH |
|
Included hardware
|
Item |
Qty |
Notes |
|---|---|---|
|
Accordion M1 unit |
1 |
Pre-configured with the modules below. |
|
ESH10000568 — MPIO-96 SPI Module |
1 |
SO-DIMM slot. |
|
ESH10000355 — 6× IDC N-Top Breakout Module |
1 |
N-Top position. |
|
ESH10000662 — Mini-PSU |
1 |
COMTOP position. |
|
USB-C power supply and cable |
1 |
130 W USB-PD supply with a 1 m USB-C cable. |
Included software licences (lifetime)
|
Product |
Licence |
Notes |
|---|---|---|
|
Accordion Shell |
Lifetime, single-unit |
CLI tool. Installed via |
|
Accordion Pilot |
Lifetime, single-unit |
Windows GUI. Installer: https://esharp.blob.core.windows.net/accordionpilot/setup.exe. |
The Web API, the Python package accordionq2 and the .NET client AccordionQ2.WebApiClient are open clients and need no separate licence.
Channel summary — MPIO-96 (ESH10000568) via IDC (ESH10000355)
|
Parameter |
Value |
|---|---|
|
User channels |
96, bidirectional |
|
Modes per channel |
Analog input, analog output, pseudo-digital I/O |
|
ADC / DAC resolution |
12-bit / 12-bit |
|
Analog range |
0–5 V typical (AD5592R 2× mode) |
|
Pseudo-digital thresholds |
Programmable VL / VH per channel |
|
Open-drain emulation |
Supported (set VH < 0) |
|
Floating-output emulation |
Supported (set VL < 0) |
|
High-speed acquisition |
Supported, via |
|
Calibration |
Per-channel gain and offset |
|
Max voltage / current at IDC signal pin |
5 V / 2 A |
|
IDC pin-1 / pin-2 rails |
5 V / 20 V, PTC-fused at 0.25 A per connector |
|
Connector LEDs |
1 RGB LED per IDC connector, software-controlled |
Power supply — Mini-PSU (ESH10000662)
|
Parameter |
Value |
|---|---|
|
Channels |
2, independent |
|
Output voltage |
5–24 V per channel |
|
Output current |
1.5 A continuous per channel up to 20 V output; about 30 W per channel above 20 V |
|
Current-limit accuracy |
±5 mA after two-point calibration (0–1.5 A) |
|
Current-limit resolution |
≤ 0.75 mA |
|
Load transient (0 → 1.5 A) |
≤ 1 % overshoot, recovery ≤ 5 µs |
|
Output stability |
≤ ±0.1 % over 8 h at 24 V / 1 A |
|
Readback |
Output voltage and current per channel |
|
Per-channel enable |
Yes, software-controlled |
|
Thermal |
≤ 50 °C hotspot at full load, 25 °C ambient |
For per-module detail see ESH10000568, ESH10000355 and ESH10000662.
Manual
Hardware
Power-on procedure
-
Connect the bundled USB-C power supply to mains.
-
Connect the USB-C cable to the unit's power input.
-
Connect Ethernet to the same network as the controlling PC.
-
Depending on how the unit is set up, it starts when power is applied, or when you press the power button.
-
Wait about 1 minute for the unit to boot. The fan runs at full speed until the Accordion process takes over.
-
The unit is reachable by hostname or by its DHCP-assigned IP address.
The Mini-PSU outputs are off at boot and must be enabled in software.
Connecting a fixture
-
Signal lines: standard 20-pin (2×10, 2.54 mm pitch) IDC ribbon cable from the six IDC connectors to the fixture. Check pin-1 orientation before mating.
-
Programmable supplies: wire the DUT supply leads to the Mini-PSU output connector (VOUT1, VOUT2, GND).
Power down the unit before changing fixture wiring.
Software
The unit runs the standard Accordion software. Use the Web API directly, or through Accordion Pilot, Accordion Shell, the Python package accordionq2, the .NET client AccordionQ2.WebApiClient or TestStand — see the Accordion A2 Lite page for install commands and examples; the same clients apply.
-
MPIO channels:
{ModuleIndex}.ESH10000568.MPIO{00–95}. All boot in INPUT mode. -
The IDC breakout is passive; its pins are addressed through the MPIO-96 channels.
-
Mini-PSU: set voltage and current limit per channel, then enable the output. Read back output voltage and current.
Pinout
IDC signal connectors (ESH10000355)
|
Connector |
Signals |
MPIO channels |
|---|---|---|
|
J1 |
DATA[0–15] |
MPIO00–MPIO15 |
|
J2 |
DATA[16–31] |
MPIO16–MPIO31 |
|
J3 |
DATA[32–47] |
MPIO32–MPIO47 |
|
J4 |
DATA[48–63] |
MPIO48–MPIO63 |
|
J5 |
DATA[64–79] |
MPIO64–MPIO79 |
|
J6 |
DATA[80–95] |
MPIO80–MPIO95 |
Pin 1 = +5 V, pin 2 = +20 V (both PTC-fused at 0.25 A), pins 3–20 = 16 signals and GND returns. See the ESH10000355 page for the full pin layout.
Mini-PSU output connector (ESH10000662, J2, 4-pin)
|
Pin |
Signal |
|---|---|
|
1 |
VOUT1 |
|
2 |
GND |
|
3 |
GND |
|
4 |
VOUT2 |
Related pages
E-Sharp AB (E#) · Götgatan 3, 244 32 Kävlinge, Sweden · https://www.esharp.se
Author: Gustav · Date: 2026-11-10 · Revision: 1
This document was prepared by Gustav with the assistance of AI.