Accordion M1 Tone & Power Supply
Product brief
The Accordion M1 Tone & Power Supply is a ready-to-run configuration of the compact Accordion M1 platform for audio test in PCBA test, NPI and production test. It generates and analyses line-level audio on the unit itself and supplies the DUT from a two-channel programmable power supply, all on one network-attached node.
The unit contains an Accordion M1 mainboard with a Raspberry Pi 4, pre-fitted with three modules:
-
ESH10000560 Tone Audio Module — audio generation and analysis at 96 kSps / 24 bit; all signal processing runs on the module, and only settings and results cross to the host.
-
ESH10000612 Tone Audio N-Top — ten SMA jacks (eight inputs, two outputs) with RGB indicator LEDs, and a GPIO / power header.
-
ESH10000662 Mini-PSU (COMTOP) — two independent programmable outputs, 5–24 V, up to 1.5 A each.
The M.2 slot is free for expansion.
The unit ships with lifetime licences for Accordion Shell and Accordion Pilot.
Typical use cases:
-
Audio subsystem test: frequency, level, THD and SNR measurements.
-
Tone generation for microphone, speaker-path and audio-codec test.
-
Production fixtures that power the DUT and test its audio path from the same node.
Key constraints:
-
All audio interfaces are line level. Digital audio (I²S) is internal and not available externally.
-
Sample rate (96 kSps) and sample depth (24 bit) are fixed.
-
The eight inputs form four stereo pairs. Left and right of each pair are on separate, simultaneously sampled ADC channels; one pair is captured at a time.
-
Mini-PSU: 1.5 A continuous per channel up to 20 V output; above 20 V each channel is limited to about 30 W.
-
Pin 2 of the GPIO / power header carries the 20 V supply, next to 3.3 V GPIO pins — see the warning under Pinout.
-
Powered over USB-C (USB-PD) at 20 V. The bundled power supply is the only supported supply.
Datasheet
System
|
Parameter |
Value |
Notes |
|---|---|---|
|
Product name |
Accordion M1 Tone & Power Supply |
|
|
Part number |
ESH10000755 |
|
|
Platform |
Accordion M1 (mainboard ESH10000597) |
|
|
Controller |
Raspberry Pi 4, 4 GB |
|
|
Firmware |
Accordion 6.0.0 or later |
|
|
Power input |
USB-C (USB-PD) 20 V, via the bundled 130 W power supply |
Use the bundled supply only. |
|
Power-on |
At power-up or with the power button |
Optional, set at delivery. |
|
Input protection |
eFuse, 5 A current limit, overvoltage cut-off above 21 V |
|
|
Network interface |
Ethernet, Wifi |
|
|
Module slots populated |
SO-DIMM (Tone Audio Module), N-Top (Tone Audio N-Top), COMTOP (Mini-PSU) |
|
|
Module slots free |
1× M.2 |
|
|
Cooling |
Active, one fan, speed-regulated by the Accordion process |
Full speed at boot. |
|
Enclosure |
Hammond 1455K1201BU with E# front, top and back panels |
|
|
Dimensions (L × W × H) |
120 × 78 × 43 mm |
|
|
Weight |
324 g |
|
|
Compliance |
CE, RoHS, REACH |
|
Included hardware
|
Item |
Qty |
Notes |
|---|---|---|
|
Accordion M1 unit |
1 |
Pre-configured with the modules below. |
|
ESH10000560 — Tone Audio Module |
1 |
SO-DIMM slot. |
|
ESH10000612 — Tone Audio N-Top |
1 |
N-Top position. |
|
ESH10000662 — Mini-PSU |
1 |
COMTOP position. |
|
microSD card, 32 GB |
1 |
Pre-loaded with the Accordion image. |
|
USB-C power supply |
1 |
130 W, USB-PD. |
|
USB-C power cable |
1 |
1 m. |
Included software licences (lifetime)
|
Product |
Licence |
Notes |
|---|---|---|
|
Accordion Shell |
Lifetime, single-unit |
CLI tool. Installed via |
|
Accordion Pilot |
Lifetime, single-unit |
Windows GUI. Installer: https://esharp.blob.core.windows.net/accordionpilot/setup.exe. |
The Web API, the Python package accordionq2 and the .NET client AccordionQ2.WebApiClient are open clients and need no separate licence.
Audio (ESH10000560 via ESH10000612)
|
Parameter |
Value |
|---|---|
|
Sample rate |
96 kSps |
|
Sample depth |
24 bit |
|
Signal level |
Line level |
|
Outputs |
2 (left, right), programmable gain per channel |
|
Inputs |
8 (four stereo pairs), programmable gain |
|
Stereo capture |
One pair at a time; left and right sampled simultaneously on two ADC channels |
|
Waveforms |
Sine, square, triangle, white noise, pink noise, sweep |
|
Measurements |
Frequency, V_rms, V_pp, THD, SNR |
|
Processing |
On the module; only settings and results are exchanged with the host |
|
Audio connectors |
10 × SMA |
|
Indicator LEDs |
24 RGB, software-controlled (two per jack, four for the GPIO lines) |
|
GPIO |
6 lines, 3.3 V logic (3.6 V absolute maximum) |
Power supply — Mini-PSU (ESH10000662)
|
Parameter |
Value |
|---|---|
|
Channels |
2, independent |
|
Output voltage |
5–24 V per channel |
|
Output current |
1.5 A continuous per channel up to 20 V output; about 30 W per channel above 20 V |
|
Current-limit accuracy |
±5 mA after two-point calibration (0–1.5 A) |
|
Current-limit resolution |
≤ 0.75 mA |
|
Load transient (0 → 1.5 A) |
≤ 1 % overshoot, recovery ≤ 5 µs |
|
Output stability |
≤ ±0.1 % over 8 h at 24 V / 1 A |
|
Readback |
Output voltage and current per channel |
|
Per-channel enable |
Yes, software-controlled |
For per-module detail see ESH10000560 and ESH10000662.
Manual
Hardware
Power-on procedure
-
Connect the bundled USB-C power supply to mains.
-
Connect the USB-C cable to the unit's power input.
-
Connect Ethernet to the same network as the controlling PC.
-
Depending on how the unit is set up, it starts when power is applied, or when you press the power button.
-
Wait about 1 minute for the unit to boot. The fan runs at full speed until the Accordion process takes over.
-
The unit is reachable by hostname or by its DHCP-assigned IP address.
Audio outputs and the Mini-PSU outputs are off at boot.
Connecting a fixture
-
Audio: SMA cables to the input and output jacks (centre pin = signal, shell = GND). For stereo, connect left to the L jack and right to the R jack of the same pair.
-
GPIO and auxiliary power: the 2×5 header. Read the warning below before wiring it.
-
Programmable supplies: the Mini-PSU output connector (VOUT1, VOUT2, GND).
Power down the unit before changing fixture wiring.
Software
The unit runs the standard Accordion software. Use the Web API directly, or through Accordion Pilot, Accordion Shell, the Python package accordionq2, the .NET client AccordionQ2.WebApiClient or TestStand — see the Accordion A2 Lite page for install commands; the same clients apply.
-
Generation: choose the output channel, waveform, frequency and gain, then start. The output runs continuously on the module; no samples are streamed from the host.
-
Analysis: choose the input pair and gain, start acquisition and read back frequency, V_rms, V_pp, THD or SNR.
-
Mini-PSU: set voltage and current limit per channel, then enable the output.
To generate and analyse audio from a browser, with live readings, spectrum, waterfall and scope, use the Audio analyser in the Accordion Pilot Web UI: Web UI: Audio analyser.
Pinout
Audio jacks (ESH10000612, SMA)
|
Jack |
Signal |
Direction |
|---|---|---|
|
J4 |
IN1 L |
Input |
|
J5 |
IN1 R |
Input |
|
J6 |
IN2 L |
Input |
|
J7 |
IN2 R |
Input |
|
J8 |
IN3 L |
Input |
|
J9 |
IN3 R |
Input |
|
J10 |
IN4 L |
Input |
|
J11 |
IN4 R |
Input |
|
J12 |
OUT R |
Output |
|
J13 |
OUT L |
Output |
GPIO / power header (ESH10000612 J14, 2×5, 2.54 mm)
|
Pin |
Signal |
Pin |
Signal |
|---|---|---|---|
|
1 |
5V |
2 |
VDD (20 V) |
|
3 |
MPIO0 |
4 |
MPIO3 |
|
5 |
MPIO1 |
6 |
MPIO4 |
|
7 |
MPIO2 |
8 |
MPIO5 |
|
9 |
GND |
10 |
GND |
Warning: pin 2 carries the unit's 20 V supply. The MPIO pins are 3.3 V logic with a 3.6 V absolute maximum. Connecting pin 2 to any MPIO pin, or to a 5 V or 3.3 V circuit, can damage the module and the DUT. Use pin 2 only for loads rated for 20 V.
Mini-PSU output connector (ESH10000662, 4-pin)
|
Pin |
Signal |
|---|---|
|
1 |
VOUT1 |
|
2 |
GND |
|
3 |
GND |
|
4 |
VOUT2 |
Related pages
E-Sharp AB (E#) · Götgatan 3, 244 32 Kävlinge, Sweden · https://www.esharp.se
Author: Gustav · Date: 2026-11-10 · Revision: 2
This document was prepared by Gustav with the assistance of AI.